Spray PU Foam Insulation in Dubai — Roofs, Villas & Warehouses
Spray PU Foam Insulation in Dubai — Roofs, Villas & Warehouses
Spray polyurethane foam reduces overheating of structures and indoor spaces, stabilising internal temperatures and lowering the load on air conditioning systems.
Spray polyurethane foam reduces overheating of structures and indoor spaces, stabilising internal temperatures and lowering the load on air conditioning systems.
Seamless insulation — no joints, no cold bridges
Thickness: 30–150 mm depending on project requirements
Adheres directly to concrete, metal, profiled sheeting, wood
Covers complex geometry, gaps and irregular surfaces
CAN BE COMBINED WITH POLYUREA WATERPROOFING
THE HEAT IN DUBAI POSES A REAL CHALLENGE FOR ANY ROOF
Dubai's climate creates constant thermal stress that reduces energy efficiency and accelerates roof ageing.
-
Roof surfaces reach 70–80°C
-
Heat transfers into the building
-
Higher cooling demand and AC costs
-
Daily thermal movement stresses roof joints
SPF forms a seamless thermal barrier that reduces heat transfer and cooling demand.
WHERE WE APPLY SPF INSULATION
The most popular
ROOF INSULATION — COMMERCIAL &
ROOF INSULATION — COMMERCIAL &
RESIDENTIAL
The primary application of SPF in Dubai. Applied to flat roofs, sloped roofs and exposed roof slabs — on commercial buildings, apartment blocks, mixed-use developments and residential properties. Can be applied internally or externally. Works over existing substrates without full demolition, assessed after inspection.
VILLAS AND RESIDENTIAL BUILDINGS
Applied to roof slabs, cavities and pitched sections. Reduces heat gain through the roof, lowers AC costs and improves indoor comfort on upper floors. In Dubai's climate, an insulated roof can significantly reduce cooling load and stabilise temperatures in occupied spaces.
WAREHOUSES, FACTORIES AND LOGISTICS FACILITIES
Large-span metal or concrete structures — warehouses, factories, logistics centres and commercial buildings — with high exposed roof surface areas. SPF applied to the underside of roof panels or external roof surfaces. Eliminates heat retention, removes condensation at panel joints.
TECHNICAL SPECIFICATIONS
Seamless layer — no joints, no cold bridges
Thickness: 30–150 mm (matched to heat load and project requirements)
Adheres directly to concrete, metal, wood — no mechanical fixing required
-
Foam density 30–60 kg/m³
-
Thermal conductivity ~0.020–0.028 W/m·K
-
Operating range -60°C to +100°C
-
Layer per pass 10–30 mm
-
UV protection required for outdoor use
SOLUTIONS USED IN EUROPE OR CIS COUNTRIES OFTEN FAIL IN DUBAI
Constant heat, intense UV exposure and humidity create conditions where standard systems degrade faster. We select and configure polyurethane foam systems specifically for UAE operating conditions.
High-adhesion primers formulated for UAE substrates and humidity levels
Reinforced detail treatment in high-load and connection zones
Protective topcoats against mechanical wear and UV degradation
INSULATION AND WATERPROOFING IN ONE SYSTEM
One roof system. Two layers of protection.
SPF reduces heat transfer, while polyurea creates a seamless waterproofing barrier. Together they deliver long-term performance under UAE operating conditions.
The result is a complete roof system engineered for the UAE: seamless waterproofing, continuous insulation, fewer failure points and a single contractor for the entire installation.
Thermal insulation + seamless waterproofing — one complete roof system.
Application process
How we work
The service life of insulation is not defined after completion — it is formed during execution.
01
Site inspection
Surface condition, substrate type, access and heat exposure.
02
Surface preparation
Cleaning, degreasing, repair of defects. Any deviation at this stage affects the final result.
03
Application in passes
10–30 mm per pass to reach target thickness. Layer uniformity and parameters strictly controlled.
04
UV/weather protection
All external applications covered with UV-resistant coating.
Site inspection
Surface condition, substrate type, access and heat exposure.
Surface preparation
Cleaning, degreasing, repair of defects. Any deviation at this stage affects the final result.
Application in passes
10–30 mm per pass to reach target thickness. Layer uniformity and parameters strictly controlled.
UV/weather protection
All external applications covered with UV-resistant coating.
Case studies — local projects
Dubai Industrial Area
Warehouse roof
Scope: metal roof
2,400 m²
Timeline:
4 days
Solution: SPF 80 mm + polyurea protective coat
System installed: SPF insulation and polyurea protective coat installed; project handed over within agreed timeline
Dubai Industrial Area
Warehouse roof
Scope: metal roof
2,400 m²
Timeline:
4 days
Solution: SPF 80 mm + polyurea protective coat
System installed: SPF insulation and polyurea protective coat installed; project handed over within agreed timeline
Dubai Industrial Area
Warehouse roof
Scope: metal roof
2,400 m²
Timeline:
4 days
Solution: SPF 80 mm + polyurea protective coat
System installed: SPF insulation and polyurea protective coat installed; project handed over within agreed timeline
FAQ — PU foam insulation
The service life of waterproofing is not defined after completion — it is formed during execution.
Yes, with correct component temperature management. We plan outdoor application times to maintain material performance.
Yes. Exposed foam degrades under UV, so all external applications are finished with a UV-resistant protective coating.
In most cases yes, provided the existing surface is sound, dry and properly prepared. We confirm this on inspection.
It is well suited to new build, where insulation and waterproofing can be specified together as a single roof system.